日本PEACOCK孔雀量表 EG-1 外徑測量計

]資料

點擊看大圖

如果您對該產品感興趣的話,可以 sendmsg

給我留言
產品名稱: 日本PEACOCK孔雀量表 EG-1 外徑測量計
產品型號: EG-1
產品廠商: 深圳市鑫騰明計量?jī)x器商行
產品報價:

產品特點

日本PEACOCK孔雀量表 EG-1 外徑測量計

日本PEACOCK孔雀量表 EG-1 外徑測量計 的詳細介紹

Easy measurement of thickness, outer diameter, inner diameter and depth.

Handy size with excellent functions.

Minimum reading : 0.1mm.

EG-1	for measurement of inner diameter, outer diameter and thickness.

EG-2	for measurement of inner diameter, outer diameter and thickness and depth.

How to use Snap Caliper ( EG-1, EG-2 )

To measure thickness and diameter of balls :
(1)	First, press down a knob to check whether a pointer shows 0.
(2)	As shown in the drawing II , put an object for measurement between a contact point
	and anvil, and read a position of pointer on a dial plate. A division of scale is 0.1 mm,
	so read the values on the dial 1, 2, 3... as 1, 2, 3 mm... ( After one rotation, it shows 11,
	12, 13 mm... )
(3)	One rotation of a pointer shows 10 mm. Check whether it is first or second rotation by
	reading a spindle scale indication.
	( Example ):A pointer shows 6 at your measurement:
	1st rotation --> 6 mm, 2nd rotation --> 16mm

To measure groove width and inner diameter :
(1)	Press down a knob and have a contact point and anvil contacted fast, then rotate an
	outer frame of gauge so that a division of 3 on a dial plate meets a position of pointer.
(2)	Pressing down a knob by your fingers, insert the tips of contact point and anvil into the
	inside of an object for measurement, and slowly release a knob, as shown in the
	drawing III
	( Notice ) :Measure an object at right angles to a groove. If you measure it diagonally,
	a value larger than the actual one will be indicated.

To measure depth and step depth -( EG-2 only is available. )
(1)	Rotate an outer frame of gauge so that a pointer meets 0 on a dial plate, by putting
	a flat plate on the reference level of gauge. ( If there is no adequate plate, put your
	gauge upside down, and press the reference level of gauge on a flat table ).
(2)	Press your gauge down to the measuring part of an object for measurement, as
	shown in the drawing IV

Major Specifications
(1)	A division of scale		0.1mm
(2)	Measuring Range	for measurement of thickness	0 ～ 20mm
		for measurement of inner diameter	3 ～ 23mm
		for measurement of depth	0 ～ 20mm
(3)	Weight	EG-1 ; 97g	EG-2 ; 100g

Remarks
	After your finising measurements of internal diameter and step depth, adjust a pointer so
	as to meet 0 on a dial plate for thickness measurement.

產品留言

相關產品